Shock Doctor Gel Max Power Mouthguard - Red

How To Mold A Mouthguard: 7 Easy Steps For A Secure Boil And Bite Fit

Knowing how to mold a mouthguard properly makes the difference between a mouthguard that stays in place and protects the teeth, and one that falls out, feels bulky and ends up in the bottom of a hockey bag. Most athletes use a boil and bite mouthguard, which is softened in hot water and shaped to the teeth at home or in the locker room.

This guide explains why mouthguards matter, the main types, step-by-step instructions on how to mold a boil and bite mouthguard, and how to care for it. It is written for athletes, parents, coaches, athletic therapists and the teams and clinics that supply them.

Why Athletes Should Wear A Mouthguard

A mouthguard cushions blows to the face and spreads the force of an impact. It helps protect against:

  • chipped, broken or knocked-out teeth;
  • cuts to the lips, tongue and inner cheeks;
  • damage to braces and other orthodontic appliances; and
  • some injuries to the jaw.

The Ontario Dental Association recommends mouthguards for contact and collision sports such as hockey, football, rugby, lacrosse and boxing, and for any sport where there is a risk of falls or being hit in the face.

Types Of Mouthguards

Boil and bite mouthguard you can mold at home
A boil and bite mouthguard, such as the Shock Doctor Gel Max Power, is molded to the teeth after softening in hot water.
  • Stock mouthguards come ready to wear. They are inexpensive but cannot be adjusted, so they often fit poorly.
  • Boil and bite mouthguards are made from a thermoplastic that softens in hot water so it can be shaped to the teeth. They offer a much better fit than stock guards and are the most popular choice for sport.
  • Custom mouthguards are made by a dentist from an impression of the teeth. They give the best fit and are worth considering for high-level athletes or those with dental work.
  • Braces mouthguards are designed to fit over orthodontic brackets and are usually not molded, so they can adjust as the teeth move.

How To Mold A Mouthguard: Step By Step

Always follow the manufacturer’s instructions for the specific mouthguard, as times and temperatures vary. The general steps for how to mold a mouthguard of the boil and bite type are:

  1. Check the size. Make sure the mouthguard covers the upper teeth back to the molars without pressing into the gums. Trim only if the instructions allow it.
  2. Heat the water. Bring a pot of water to a boil, then remove it from the heat so it stops boiling.
  3. Soften the mouthguard. Hold it by the strap or use a slotted spoon and place it in the hot water for the time stated on the package, usually 15 to 30 seconds.
  4. Let it cool briefly. Remove the mouthguard, shake off excess water and let it sit for a few seconds so it is warm, not hot.
  5. Place and bite. Centre the mouthguard over the upper teeth, bite down firmly but gently, and suck in hard to pull the material against the teeth. Press it against the outside of the teeth with your fingers and tongue.
  6. Hold, then cool. Keep biting and sucking for the time recommended, usually around 20 to 30 seconds, then remove the mouthguard and place it in cold water to set the shape.
  7. Check the fit. The mouthguard should stay on the upper teeth without biting down, allow normal breathing and speech, and feel comfortable. If not, most boil and bite mouthguards can be remolded.

Tips For A Better Fit

Shock Doctor Microfit boil and bite mouthguard
Low-profile mouthguards such as the Shock Doctor Microfit can make breathing and talking easier.
  • Do not chew the mouthguard while molding it, as this thins the material.
  • Do not use water that is still boiling, which can deform the guard.
  • Mold the mouthguard just before the season starts, after any dental work is complete.
  • Children’s mouths change quickly, so check the fit regularly and replace guards as they grow.
  • Athletes with braces should use a braces mouthguard and check with their orthodontist before molding any guard.

Caring For A Mouthguard

Rinse the mouthguard with cold water before and after use, clean it regularly with a toothbrush and mild soap, and store it in a ventilated case. Keep it out of hot cars and direct sunlight, which can warp the shape. Replace the mouthguard if it is torn, worn or no longer fits snugly, and at least every season for growing athletes.

Mouthguards For Teams And Clinics

Dunbar Medical supplies sports teams, schools, athletic therapists and sports medicine clinics across Canada with mouthguards from Shock Doctor and Mueller, including the Shock Doctor Gel Max Power Mouthguard, Shock Doctor Microfit Mouthguard, Shock Doctor Braces Mouthguard and MuellerGuard Mouthguard. Browse our sports mouth guard range.

Frequently Asked Questions

How long do you boil a mouthguard to mold it?

Most boil and bite mouthguards are placed in water that has just come off the boil for about 15 to 30 seconds. Check the package, as times vary between brands.

Can you remold a boil and bite mouthguard?

Most can be remolded if the first fitting is not right. Follow the manufacturer’s instructions, as repeated heating can thin the material.

Should I mold a mouthguard if I have braces?

Athletes with braces should usually wear a braces mouthguard that is not molded tightly to the teeth. Check with the orthodontist first.

How do I know if my mouthguard fits?

It should stay on the upper teeth without biting down, cover the teeth back to the molars and let you breathe and talk normally.

Conclusion

Learning how to mold a mouthguard correctly takes only a few minutes and gives athletes a better-fitting, more comfortable guard that they are more likely to wear. Heat it as directed, bite and suck to shape it, cool it to set, and check the fit. For teams and clinics, contact our team about stocking mouthguards for your athletes.

Leave a Reply

Your email address will not be published. Required fields are marked *